info:eu-repo/semantics/bachelorThesis
Influencia del tipo y porcentaje de relleno, sobre la resistencia a la tracción, impacto y flexión en el polietileno tereftalato glicol (petg) procesado mediante impresión 3d-fdm.
Fecha
2021-08Autor
Valverde Vidal, Luis Rony
Institución
Resumen
En la presente investigación se evaluó la influencia del tipo de relleno y el porcentaje de
relleno en probetas de PETG (polietileno tereftalato glicol), fabricadas mediante
impresión 3D-FDM, sobre su resistencia a la tracción, resistencia al impacto y resistencia
a la flexión.
Las probetas de PETG (polietileno tereftalato glicol) fueron diseñadas en el sistema CAD,
SolidWork versión 2016. La información del diseño CAD fue llevada al software
Repetier Host, que modela con la impresora 3D. Se modelaron probetas con formato de
tracción tipo IV según norma ASTM D638, para flexión se hizo uso de la norma ASTM
D790 – 17 y para ensayo de impacto se usó la norma ISO 180. Las probetas de PETG
(polietileno tereftalato glicol) fueron fabricadas con distintos tipos de relleno: rectilineal,
panal y concéntrico; y diferentes porcentajes de relleno: 20, 40 y 60 %.
Los resultados finales muestran que para la resistencia a la tracción el valor mínimo se da
con el tipo rectilineal al 20 % de relleno con 26.65 MPa, y el valor más alto se da con el
tipo concéntrico al 60 % con 31.28 MPa.
Para la resistencia al impacto se obtuvo que el valor más bajo de resistencia al impacto se
da con el tipo concéntrico al 20 % de relleno con 3.89 KJ/m², y el valor más alto se da
con el tipo rectilineal al 60 % con 6.57 KJ/m².
Finalmente, para la resistencia a la flexión se obtuvo el valor más bajo con el tipo panal
al 20 % de relleno con 43.85 MPa, y el valor más alto se da con el tipo panal al 60 % con
60.64 MPa In the present research, the effect of the type of filler and the percentage of filler in PETG
(polyethylene terephthalate glycol) specimens, made by 3D-FDM printing, on their
tensile resistance, impact resistance and flexural resistance, were evaluated.
The PETG (polyethylene terephthalate glycol) specimens were designed in the CAD
system, SolidWork version 2016.
The CAD design information was taken to the Repetier Host software, which models with
the 3D printer. Specimens with type IV traction format were modeled according to ASTM
D638, for bending the ASTM D790 - 17 standard was used and for impact testing the ISO
180 standard was used. The PETG (polyethylene terephthalate glycol) specimens were
manufactured with different types of filling: rectilinear, honeycomb and concentric; and
different filling percentages: 20, 40 and 60%.
The final results show that for the tensile strength the minimum value is given with the
rectilinear type at 20% filling with 26.65 MPa, and the highest value is given with the
concentric type at 60% with 31.28 MPa.
For impact resistance, it was obtained that the lowest value of impact resistance is given
with the concentric type at 20% fill with 3.89 KJ / m², and the highest value is given with
the rectilinear type at 60% with 6.57 KJ / m².
Finally, for the flexural strength, the lowest value was obtained with the honeycomb type
at 20% filling with 43.85 MPa, and the highest value is given with the honeycomb type
at 60% with 60.64 MPa.