The morphology and length scale of the phases forming the microstructure of sliding bearing alloys are known to affect wear, mechanical and corrosion resistances. Al-Sn alloys have good anti-frictional properties due to the presence of Sn. However, with the current trends in engine design, these alloys are not able to support the demanded heavy loads. An alternative way to reach this requirement can be the alloying with third elements such as Si and Cu. Despite the importance of their application properties, studies on the development of microstructures of these multicomponent alloys are rare in the literature. In the present investigation Al-Sn-(Cu;Si) alloys were directionally solidified (DS) under transient heat flow conditions, and a thorough characterization is performed including experimental growth rates and cooling rates, segregation, optical and scanning electron microscopies and primary dendrite arm spacings, λ1. Experimental growth laws are proposed relating the dendritic spacing to solidification thermal parameters. Furthermore, the scale of the dendritic morphology, the distribution of second phases in interdendritic regions and the macrosegregation pattern are shown to affect the hardness along the length of the DS castings. Hall-Petch type equations are proposed relating hardness to λ1.72 3142Zhu, M., Gao, Y., Chung, C.Y., Che, Z.X., Luo, K.C., Li, B.L., Improvement of the wear behaviour of Al-Pb alloys by mechanical alloying (2000) Wear, 242, pp. 47-53Pathak, J.P., Mohan, S., Tribological behaviour of conventional Al-Sn and equivalent Al-Pb alloys under lubrication (2003) Bull Mater Sci, 26, pp. 315-320Noskova, N.I., Vil'danova, N.F., Filippov, Y.I., Churbaev, R.V., Pereturina, I.A., Korshunov, L.G., Preparation, deformation, and failure of functional Al-Sn and Al-Sn-Pb nanocrystalline alloys (2006) Phys Met Metallogr, 102, pp. 646-651Ran, G., Zhou, J., Xi, S., Li, P., Microstructure and morphology of Al-Pb bearing alloy synthesized by mechanical alloying and hot extrusion (2006) J Alloy Compd, 419, pp. 66-70Wu, X.F., Zhang, G.A., Influence of Sn content on the microstructure and dry sliding wear behaviour of hypereutectic Al-20Si alloy (2011) Adv Mater Res, pp. 265-268Lu, Z.C., Zeng, M.Q., Gao, Y., Zhu, M., Significant improvement of wear properties by creating micro/nano dual-scale structure in Al-Sn alloys (2012) Wear, 296, pp. 469-478Liu, X., Zeng, M.Q., Ma, Y., Zhu, M., Promoting the high load-carrying capability of Al-20wt%Sn bearing alloys through creating nanocomposite structure by mechanical alloying (2012) Wear, pp. 387-394Agafii, V.I., Petrenko, V.I., Fomichev, V.M., Yurchenko, V.I., Yurchenko, E.V., Dikusar, A.I., Electrospark alloying for deposition on aluminum surface of Al-Sn coatings and their wear resistance under dry friction (2013) Surf Eng Appl Electrochem, 49, pp. 181-188Bravo, A.E., Durán, H.A., Jacobo, V.H., Ortiz, A., Schouwenaars, R., Towards new formulations for journal bearing alloys (2013) Wear, 302, pp. 1528-1535Feyzullahoğlu, E., Ertürk, A.T., Güven, E.A., Influence of forging and heat treatment on wear properties of Al-Si and Al-Pb bearing alloys in oil lubricated conditions (2013) Trans Nonferr Met Soc, 23, pp. 3575-3583Lu, Z.C., Zeng, M.Q., Gao, Y., Zhu, M., Minimizing tribolayer damage by strength-ductility matching in dual-scale structured Al-Sn alloys: a mechanism for improving wear performance (2013) Wear, 304, pp. 162-172Rusin, N.M., Skorentsev, A.L., Improving the tribological properties of self-lubricating Al-Sn alloys by their severe plastic processing (2013) Appl Mech Mater, 379, pp. 110-114Sui, B., Zeng, J.M., Chen, P., Liang, L.H., Gan, W.K., Lu, J.B., Study on tribological performance of Al2O3 particle reinforced the Al-Sn bearing alloy (2014) Appl Mech Mater, pp. 137-140Mittal, R., Tomar, A., Singh, D., Wear behavior of disk shape spray formed Al-Si-Pb alloys (2014) J Mater Eng Perform, 23, pp. 975-981Yuan, G.C., Li, Z.J., Lou, Y.X., Zhang, X.M., Study on crystallization and microstructure for new series of Al-Sn-Si alloys (2000) Mater Sci Eng, A, 280, pp. 108-115Yuan, G.C., Zhang, X.M., Lou, Y.X., Li, Z.J., Tribological characteristics of new series of Al-Sn-Si alloys (2003) Trans Nonferrous Met Soc China, 13, pp. 774-780Kong, C.J., Brown, P.D., Harris, S.J., McCartney, D.G., The microstructures of a thermally sprayed and heat treated Al-20wt%Sn-3wt%Si alloy (2005) Mater Sci Eng A-Struct, 403, pp. 205-214Pramanick, A., Chatterjee, S., Bhattacharya, V., Chattopadhyay, K., Synthesis and microstructure of laser surface alloyed Al-Sn-Si layer on commercial aluminum substrate (2005) J Mater Res, 20, pp. 1580-1589Abd El-Salam, F., Abd El-Khalek, A.M., Nada, R.H., Wahab, L.A., Zahran, H.Y., Thermally induced structural and mechanical variations in ternary Al-Si based alloys (2009) Mater Sci Eng A-Struct, 527, pp. 281-286Abd El-Salam, F., Abd El-Khalek, A.M., Nada, R.H., Wahab, L.A., Zahran, H.Y., Effect of Sn content on the structural and mechanical properties of Al-Si alloy (2010) Mater Sci Eng, A, 527, pp. 1223-1229Nada, R.H., Abd El-Salam, F., Abd El-Khalek, A.M., Wahab, L.A., Zahran, H.Y., Effect of cyclic stress reduction on the creep parameters of Al-Si alloy with Ag and Sn additions (2012) Mater Sci Eng A-Struct, 552, pp. 486-492Rameshkumara, T., Rajendran, I., Mechanical and tribological properties on Al-Sn-Si alloy-based plain bearing material (2013) Tribol Trans, 56, pp. 268-274Marrocco, T., Driver, L.C., Harris, S.J., McCartney, D.G., Microstructure and properties of thermally sprayed Al-Sn-based alloys for plain bearing applications (2006) J Therm Spray Technol, 15, pp. 634-639Kotadia, H.R., Doernberg, E., Patel, J.B., Fan, Z., Schmid-Fetzer, R., Solidification of Al-Sn-Cu immiscible alloys under intense shearing (2009) Metall Mater Trans A, 40 (A), pp. 2202-2211Kotadia, H.R., Das, A., Doernberg, E., Schmid-Fetzer, R., A comparative study of ternary Al-Sn-Cu immiscible alloys prepared by conventional casting and casting under high-intensity ultrasonic irradiation (2011) Mater Chem Phys, 131, pp. 241-249Pola, A., Montesano, L., Gelfi, M., Roberti, R., Semisolid processing of Al-Sn-Cu alloys for bearing applications (2013) Solid State Phenom, pp. 562-568Zhai, W., Hu, L., Geng, D.L., Wei, B., Thermodynamic properties and microstructure evolution of ternary Al-10%Cu-x%Sn immiscible alloys (2015) J Alloy Compd, 627, pp. 402-409Lu, Z.C., Gao, Y., Zeng, M.Q., Zhu, M., Improving wear performance of dual-scale Al-Sn alloys: the role of Mg addition in enhancing Sn distribution and tribolayer stability (2014) Wear, 309, pp. 216-225Freitas, E.S., Spinelli, J.E., Casteletti, L.C., Garcia, A., Microstructure-wear behavior correlation on a directionally solidified Al-In monotectic alloy (2013) Tribol Int, 66, pp. 182-186Freitas, E.S., Silva, A.P., Spinelli, J.E., Casteletti, L.C., Garcia, A., Inter-relation of microstructural features and dry sliding wear behavior of monotectic Al-Bi and Al-Pb alloys (2014) Tribol Lett, 55, pp. 1392-1400Cruz, K.S., Meza, E.S., Fernandes, F.A.P., Quaresma, J.M.V., Casteletti, L.C., Garcia, A., Dendritic arm spacing affecting mechanical properties and wear behavior of Al-Sn and Al-Si alloys directionally solidified under unsteady-state conditions (2010) Metall Mater Trans A, 41 A, pp. 972-984Osório, W.R., Spinelli, J.E., Cheung, N., Garcia, A., Secondary dendrite arm spacing and solute redistribution effects on the corrosion resistance of Al-10wt%Sn and Al-20wt%Zn alloys (2006) Mater Sci Eng, A, 420, pp. 179-186Osório, W.R., Freitas, E.S., Garcia, A., Corrosion performance based on the microstructural array of Al-based monotectic alloys in a NaCl solution (2014) J Mater Eng Perform, 23, pp. 333-341Sumida, M., Band structure formation in peritectic Fe-Co and Fe-Ni alloys (2003) Mater Trans, 44, pp. 1351-1358Ourfali, M.F., Todd, I., Jones, H., Effect of solidification cooling rate on the morphology and number per unit volume of primary Mg2Si particles in a hypereutectic Al-Mg-Si alloy (2005) Metall Mater Trans A, 36, pp. 1368-1372Li, H., Zhao, J., Zhang, Q., He, J., Microstructure formation in a directionally solidified immiscible alloy (2008) Metall Mater Trans A, 29, pp. 3308-3316Kaya, H., Engin, S., Böyük, U., Çadirli, E., Maraşli, N., Unidirectional solidification of Zn-rich Zn-Cu hypoperitectic alloy (2009) J Mater Res, pp. 3422-3431Zhang, Y., Ma, S.G., Qiao, J.W., Morphology transition from dendrites to equiaxed grains for AlCoCrFeNi high-entropy alloys by copper mold casting and Bridgman solidification (2012) Metall Mater Trans A, 43, pp. 2625-2630Hu, X., Li, Y., Liu, Y., Min, Z., Developments of high strength Bi-containing Sn0.7Cu lead-free solder alloys prepared by directional solidification (2015) J Alloy Compd, 625, pp. 241-250Zhong, H., Li, S., Kou, H., Li, J., The solidification path related columnar-to-equiaxed transition in Ti-Al alloys (2015) Intermetallics, 59, pp. 81-86Rohatgi, P.K., Pasciak, K., Narendranath, C.S., Ray, S., Sachdev, A., Evolution of microstructure and local thermal conditions during directional solidification of A356-SiC particle composites (1994) J Mater Sci, 29, pp. 5357-5366Şahin, H.M., Kocatepe, K., Kayikci, R., Akar, N., Determination of unidirectional heat transfer coefficient during unsteady-state solidification at metal casting-chill interface (2006) Energy Convers Manage, 47, pp. 19-34Kumar, A., Dutta, P., Numerical studies on columnar-to-equiaxed transition in directional solidification of binary alloys (2009) J Mater Sci, 44, pp. 3952-3961Goulart, P.R., Spinelli, J.E., Cheung, N., Ferreira, I.L., Garcia, A., Cellular growth during transient solidification of hypoeutectic Al-Fe alloys (2009) J Alloy Compd, 470, pp. 589-599Mirković, D., Gröbner, J., Schmid-Fetzer, R., Liquid demixing and microstructure formation in ternary Al-Sn-Cu alloys (2008) Mater Sci Eng, A, 487, pp. 456-467Boeira, A.P., Ferreira, I.L., Garcia, A., Alloy composition and metal/mold heat transfer efficiency affecting inverse segregation and porosity of as-cast Al-Cu alloys (2009) Mater Des, 30, pp. 2090-2098Pickering, E.J., Macrosegregation in steel ingots: the applicability of modelling and characterisation techniques (2013) ISIJ Int, 53, pp. 935-949Ferreira, I.L., Lins, J.F.C., Moutinho, D.J., Gomes, L.G., Garcia, A., Numerical and experimental investigation of microporosity formation in a ternary Al-Cu-Si alloy (2010) J Alloy Compd, 503, pp. 31-39Bouchard, D., Kirkaldy, J.S., Prediction of dendrite arm spacings in unsteady and steady-state heat flow of unidirectionally solidified binary alloys (1997) Metall Mater Trans B, 28, pp. 651-663Spinelli, J.E., Cheung, N., Garcia, A., On array models theoretical predictions versus measurements for the growth of cells and dendrites in the transient solidification of binary alloys (2011) Philos Mag, 91, pp. 1705-1723Rocha, O.L., Siqueira, C.A., Garcia, A., Heat flow parameters affecting dendrite spacings during unsteady-state solidification of Sn-Pb and Al-Cu alloys (2003) Metall Mater Trans A, 34, pp. 995-1006