Buscar
Mostrando ítems 1-10 de 31
Comparison of morphologies and mechanical properties of crosslinked epoxies modified by polystyrene and poly(methyl methacrylate)) or by the corresponding block copolymer polystyrene-b-poly(methyl methacrylate)
(Elsevier, 2005-03)
Polystyrene (PS, Mn=28,400, PI=1.07), poly(methyl methacrylate) (PMMA, Mn=88,600, PI=1.03), and PS (50,000)-b-PMMA (54,000) (PI=1.04), were used as modifiers of an epoxy formulation based on diglycidyl ether of bisphenol ...
Control of morphologies and mechanical properties of thermoplastic-modified epoxy matrices by addition of a second thermoplastic
(John Wiley & Sons Ltd, 2003-09)
Ternary mixtures based on stoichiometric mixtures of the diglycidyl ether of bisphenol-A (DGEBA) and 4,4′-diaminodiphenyl sulfone (DDS) and two miscible thermoplastics, poly(methyl methacrylate) (PMMA) and the poly(hydroxy ...
Development of a bilayer coating to improve the adhesion between stainless steel and in situ-polymerized poly(methyl methacrylate)
(John Wiley & Sons Inc, 2007-08)
A bilayer coating was developed that may be applied over a stainless steel surface to enhance the adhesive strength with in situ-polymerized poly(methyl methacrylate). The first layer was an epoxy based on diglycidyl ether ...
Microcomposites of poly(ε-caprolactone) and poly(methyl methacrylate) prepared by suspension polymerization in the presence of poly(ε-caprolactone) macromonomer
(Wiley VCH Verlag, 2002-12)
Poly(methyl methacrylate)-poly(ε-caprolactone) (PMMA/PCL) microparticles were synthesized by suspension polymerization of methyl methacrylate in the presence of PCL. The incorporation of a small amount of a macromonomer, ...
Miscibility of blends of poly(methyl methacrylate) and oligodiols based on a bisphenol A nucleus and ethylene oxide or propylene oxide branches
(Elsevier, 2004-09)
Cloud-point curves of blends of poly(methyl methacrylate) (PMMA) with a series of oligodiols based on a bisphenol A nucleus and short branches of poly(ethylene oxide) or poly(propylene oxide) (BPA-EO or BPA-PO), and with ...
Double phase separation induced by polymerization in ternary blends of epoxies with polystyrene and poly(methyl methacrylate)
(American Chemical Society, 2001-04)
Ternary blends based on a stoichiometric mixture of diglycidyl ether of bisphenol A (DGEBA) and 4,4'-diaminodiphenyl sulfone (DDS), monodisperse polystyrene (PS, 8.3 × 104 g/mol), and monodisperse poly(methyl methacrylate) ...
Poly(methyl methacrylate)-modified vinyl ester thermosets: Morphology, volume shrinkage, and mechanical properties
(John Wiley & Sons Inc, 2007-12)
Thermoset materials obtained from styrene/vinyl ester resins of different molecular weights modified with poly(methyl methacrylate) (PMMA) were prepared and studied. Scanning electron microscopy and transmission electron ...
Silver nanowires in poly(methyl methacrylate) as a conductive nanocomposite for microfabrication
(Institute of Physics Publishing, 2016-09)
Anovel nanocomposite resist is presented based on AgNWs dispersed in poly(methyl methacrylate). It is shown that this nanocomposite resist displays sheet resistances below 10 O sq-1 for concentrations of AgNWs higher than ...